The length of the immersed part of the wood is 0.2m.
What is density?The density is the ratio of the mass and the volume of the object. It is denoted by ρ.
ρ = mass/Volume = m/V
Volume = Area of cross-section A x height h
Given is a piece of wood of mass 40g =0.04kg and uniform cross-sectional area A= 2cm² =2x10⁻⁴ m² floats upright in water.
The density of water ,ρ = 1000 kg/m³
The density related to length of part immersed is
1000 = 0.04/ (2x10⁻⁴ x h)
h = 0.2m
Thus, the length of the immersed part of the wood is 0.2m.
Learn more about density.
https://brainly.com/question/9215083
#SPJ1
(
the average power transferred to the solar panels by sunlight is 26 000 w
calculate the average energy transferred to the solar panels in 30 seconde
use the equations
energy transferred = power time
Answer:
P = E / t definition of power is energy / unit time
1 W = 1 Joule / sec definition of 1 Watt of power
E = 2.6E4 J/s * 30 s = 7.8E5 Joules = 780,000 Joules
The average power transferred to the solar panels by sunlight is 26 000 w. The average energy transferred to the solar panels in 30 seconds is 780,000 joules.
To calculate the average energy transferred to the solar panels in 30 seconds, we can use the equation:
Energy transferred = Power × Time
Given that the average power transferred to the solar panels is 26,000 watts and the time is 30 seconds, we can substitute these values into the equation:
Energy transferred = Power × Time
Energy transferred = 26,000 × 30
Energy transferred = 780,000 watt-seconds
Since the watt-second is equivalent to the joule (J), the energy transferred to the solar panels is 780,000 joules.
Therefore, the average energy transferred to the solar panels in 30 seconds is 780,000 joules.
To know more about energy and power:
https://brainly.com/question/34423421
#SPJ5
if line segment g f = 3.2 ft, which is a possible measure of line segment t s? 1.6 ft 3.0 ft 3.2 ft 4.0 ft\
By applying the relationship of side lengths to interior angles in a triangle, a possible measure of line segment TS is 4.0 ft.
The relationship of sides to interior angles in a triangle.In Geometry, the relationship of side lengths to interior angles in a triangle include the following:
The shortest side length is always opposite of the smallest interior angle.The longest side length is always opposite of the largest interior angle.Based on the above theory, we can logically deduce that angle GF < TS or TS > GF because 42° is greater than 56°.
TS > 3.2 ft.
Therefore, a possible measure of line segment TS is 4.0 ft.
Read more on interior angle here: https://brainly.com/question/14379552
#SPJ1
Complete Question:
In the triangles, TR = GE and SR = FE. If Line segment G F = 3.2 ft, which is a possible measure of Line segment TS? 1.6 ft 3.0 ft 3.2 ft 4.0 ft.
A crane does exactly 1800 J of work to lift a steel beam from the ground. The beam is accidentally dropped and falls back to its starting position in 0.9 s. What is the mass of the beam
Answer:
Explanation:
1800x0.9=1620kg
5. Calculate the volume of a cube with the following measurements.
Length= 5 cm
Height = 10 cm
Width = 16 cm
O 31 cubic cm
50 cubic cm
O 800 cubic cm
O400 cubic cm
17. what does it mean if a personality
test is reliable?
a. a reliable test will give consistent
results over time.
b. a reliable test reveals forgotten
experiences.
c. a reliable test has strong personal
bias.
d. a reliable test accurately predicts?
your actions.
A Personality test is said to be reliable because (A). a reliable test will give consistent results over time.
Meaning of Personality testPersonality test can be defined as a test that can be used to verify or ascertain an individuals personality.
Personality test is a test that is carried out by different organizations to help to help them know the individuals in that organization and to help others know how to relate and work with them.
In conclusion, A Personality test is said to be reliable because a reliable test will give consistent results over time.
Learn more about Personality test: https://brainly.com/question/1360758
#SPJ1
Answer:
a.
Explanation:
Can you explain why number 3 is correct?
Q19. Which waves would be found at the surface at regions A and C?
1. P waves
2. S waves
3. No waves
The correct answer was number 3. But I don’t know why :(
Which form of energy is converted to electrical energy in a voltaic cell?.
Answer:
chemical energy is converted to electrical energy in a voltaic cell.
Greta is on the chairlift going up the mountain when one of her skis falls off.
The ski has a mass of 5 kg and hits the snow below with a speed of 72 km/h.
How high is the chairlift above the snow when the ski falls off?
(Ignore air resistance.)
The height of the chairlift above the snow when the ski falls off is determined as 20.4 m.
Conservation of energy
The height of the chairlift is calculated from the principle of conservation of mechanical energy as shown below;
P.E = K.E
mgh = ¹/₂mv²
gh = ¹/₂v²
h = v²/2g
where;
v is speed of the ski when it hits the snow below = 72 km/h = 20 m/sg is acceleration due to gravityh = (20)²/(2 x 9.8)
h = 20.4 m
Thus, the height of the chairlift above the snow when the ski falls off is determined as 20.4 m.
Learn more about conservation of energy here: https://brainly.com/question/24772394
#SPJ1
For an object on a flat surface, the force of gravity is 15 newtons downward and the normal force is 15 newtons upward. The applied force is 10 newtons toward the left and the frictional force is 8 newtons toward the right. What is the magnitude and direction of the net force?
2 newtons toward the right
2 newtons upward
2 newtons toward the left
2 newtons downward
Answer:
There is a net force of 2 N to the left.
With 8 N to the left the up/down and left/right forces are in balance.
The force left over is 2 N to the left.
Which statement belongs to daltons atomic theory
Atoms cannot be broken down into smaller pieces is the statement belongs to daltons atomic theory. Option B is correct.
What is an atom?The atom consists of matter that may be split without releasing electrical charges. It's also the smallest unit of matter with chemical element features.
The complete question is:
"Which statements belong to Dalton's atomic theory? Select all that apply.
A)Atoms cannot be created or destroyed.
B)Atoms cannot be broken down into smaller pieces.
C)All atoms of an element are identical.
D)Chemical reactions cause atoms to be rearranged."
According to Dalton's atomic hypothesis, atoms cannot be broken down into smaller bits.
Hence, option B is correct.
To learn more about the atom refer to the link;
https://brainly.com/question/1566330
#SPJ1
Gravitation always does negative work. question 48 options: true false
The statement indicating that 'Gravitation always does negative work' is FALSE.
What is Gravitation?Gravitation is a fundamental physical force that makes objects attract each other in the Universe.
This force (Gravitation) is required to maintain both constant positions and movement of objects.
In conclusion, the statement indicating that 'Gravitation always does negative work' is FALSE.
Learn more about Gravitation here:
https://brainly.com/question/557206
#SPJ1
Answer:false
Explanation:
The next closest star to Earth, Proxima Centuri, is 4.25 lightyears away. How far is that in meters?
Answer:
4.0208 x 10^16 meters
Explanation:
speed of light in m/s * # seconds in a year * 4.25 years =
2.99792 x 10^8 * 3600*24*365.25 * 4.25 = 4.0208 x 10^16 m
how many cubic meters of habitable space was available in skylab?
A 1,000
B 263
C 5,263
D 10,000
361 cubic meters of habitable space was available in the skylab. None of the given options are correct.
Who launched skylab?NASA launched the first American space station, called Skylab.
The fuel tank of the Saturn SIV-B rocket stage served as the Skylab's residential quarters.
Skylab's livable capacity was large in comparison to the spacecraft that American astronauts had previously used 361 cubic meters.
Skylab offered 361 cubic meters of livable area.
Hence, none of the given options is correct.
To learn more about the skylab refer;
https://brainly.com/question/23389881
#SPJ1
Which quantity is a vector quantity?
A.
displacement
B.
distance
C.
mass
D.
temperature
E.
volume
Answer:
Displacement...
Explanation:
Displacement is a vector quantity as it have both magnitude and direction...
[tex]...[/tex]
a. displacement is the correct answer
Displacement is a vector quantity
EXPLANATIONDisplacement is a vector quantity because it has both magnitude and direction.
3. why is the sum of the maximum voltages across each element in a series r l c circuit usually greater than the maximum applied voltage? doesn't that inequality violate kirchhoff's loop rule?
The sum of the maximum voltages across each element in a series RLC circuit is usually greater than the maximum applied voltage because voltages are added by vector addition.
What is the Kichoff's loop rule?Kirchhoff's loop rule states that the algebraic sum of potential differences, as well as the voltage supplied by the voltage sources and resistances, in any loop must be equal to zero.
In a series RLCcircuit, the voltages are not added by scalar addition but by vector addition.
Kirchhoff's loop rule is not violated since the voltages across different elements in the circuit are not at their maximum values.
Therefore, the sum of the maximum voltages across each element in a series RLC circuit is usually greater than the maximum applied voltage because voltages are added by vector addition.
Learn more about Kichoff's loop rule at: https://brainly.in/question/35360816
#SPJ1
The new horizons spacecraft, launched in 2006, spent 9.5 years on its journey to pluto. it derives its electric power from the heat generated by 10 kg of , which has an activity of . each decay emits an alpha particle with an energy of 5.6 mev. what is the total thermal power generated by this plutonium source
The total thermal power generated by this plutonium source is determined as 5.65 J/s.
Total thermal power generatedThe total thermal power generated by this plutonium source is determined as follows;
ΔP = Eλ
where;
E is the energy of the particles = 5.6 mevλ is the activity of the plutonium, which should be = 6.3 x 10¹⁵ s⁻¹ΔP = (5.6 mev) x (6.3 x 10¹⁵ s⁻¹)
ΔP = (5.6 x 10³ x 1.6 x 10⁻¹⁹ J) x (6.3 x 10¹⁵ s⁻¹)
ΔP = 5.65 J/s
Learn more about thermal power here: https://brainly.com/question/7541718
#SPJ1
What would happen if the atmosphere consisted of pure oxygen.
Answer:
Then our fires would become massive.
Explanation:
Hope this helps
A snail is traveling along a straight path. The snail’s velocity can be modeled by
The acceleration of the snail will be 7/13 m/sec². The acceleration is found as the rate of change of the velocity.
What is acceleration?The rate of change of velocity with respect to time is known as acceleration. According to Newton's second law, the eventual effect of all forces applied to a body is its acceleration.
The given data in the problem is;
v(t)=1.4ln(1’t²) inches per minute
0<t<15 minute
Acceleration is found as;
[tex]\rm v('t)=1.4 \times \frac{1}{1+t^2} (2t)[/tex]
Acceleration at t= 5 minute;
[tex]\rm v'(5)=\frac{1.4(2)(5)}{1+5^2} =\frac{14}{26} \\\\ v'=\frac{7}{13}[/tex]
Hence, the acceleration of the snail will be 7/13 inch per square minute.
To learn more about acceleration, refer to the link;
https://brainly.com/question/2437624
#SPJ4
-1 A 4m long wire of cross-sectional area 2.5 X 10 m² has a resistance of 5. The conductivity of the wire is (a) 2.5 X 10' m (b) 4.0 X 10' m (c) 2.5 X 10'' m¹ -1 -1 (d) 4.0 X 10''m'
Answer:
3.2 [tex]10^{-2} ohm^{-1} m^{-1}[/tex]
Explanation:
Resistance=5 ohm
Length=4m
Cross sectional area=2.5 x 10
Conductivity = 1/ resistivity
=[tex]\frac{length}{resistance x cross sectional area}[/tex]
Conductivity=4 /5 x 2.5 x 10
Conductivity=4/125
Conductivity=3.2x[tex]10^{-2}[/tex][tex]ohm^{-1} m^{-1}[/tex]
A car is moving along a straight line op is shown below it moves from O to P in 8sec and return to p to q in 6sec. What is the average velocity and the speed of the car
Answer:
The answer would be A
Explanation:
A 5000kva 230/13. 8kv single phase power transformer has a resistance of 0. 38 ohms and reactance of 1. 9 ohms
The reactance of the circuit will be 5.233×10⁻⁴ ohm. Inductive reactance is the product of 2 times π frequency and the coil inductance.
What is reactance?
When alternating electricity passes through pure reactance, it causes a voltage drop that is 90 degrees out of phase with the current.
The letter “X” is used to represent reactance in mathematics, and it is measured in ohms.
The inductive reactance of a coil is calculated using the following formula:
Inductive reactance, or XL, is the product of 2 times p (pi), and the frequency of the ac current in hertz, and the coil inductance in henries.
XL= 2πfL
Where,
f {frequency)
L (Inductance)
The reactance of the circuit is found as;
[tex]\rm R_{new}=0.38[{(\frac{1}{60} )^2][/tex]
[tex]\rm R_{new}=1.055 \times 10^{-4} \ ohm[/tex]
The inductance of the circuit is;
[tex]\rm X_{new}=1.9(\frac{1}{60} )^2\\\\X_{new}= 5.233 \times 10^{-4}\ ohm[/tex]
Hence, the reactance of the circuit will be 5.233×10⁻⁴ ohm.
To learn more about the reactance, refer to the link;
https://brainly.com/question/17129912
#SPJ4
If a lever has an input arm of 80 cm and an output arm of 20 cm, what is its ideal mechanical advantage?
Answer:
16
Explanation:
how does the egg drop project apply to everyday life
Answer:
Explanation:
It apply on how you will protect the egg because you protect the egg at all cost. It's very similar on who is protecting you, You need someone to be there for you always because an egg can't survive on it's own. Just like your life your can't be always rolling around like an egg you need to be safe and always with the person who cares for you. An egg is safe when they are together in a tray just like family and friends.
As stream discharge increases ________. only velocity increases velocity, width, and depth increase velocity, width, and depth decrease only depth increases
As stream discharge increases, only velocity increases.
What is discharge?The discharge or volume flow rate is defined as the product of the velocity of the fluid and the area of cross- section of the pipe or tube.
Discharge Q = Area A x Velocity V
Q = AV
The discharge is directly proportional to the velocity of the fluid. When discharge increases, velocity is the only physical quantity that can be changed.
Thus, As stream discharge increases, only velocity increases.
Learn more about discharge.
https://brainly.com/question/25727077
#SPJ1
What's manifestation
Answer:
Explanation:
the action or fact of showing an abstract idea.
(◑.◑)!
Manifestation (or manifesting) refers to
various pseudoscientific self-help
strategies intended to burning about
a personal goal, primary by focusing
one's thought upon the desired outcome.
The techniques are based on the law
of attraction of New Thought spiritually.
While the process involves positive
thinking, or even directing request to
"the universe", it also involves
action-steps on the part of the individual.
Manifestation has been criticised as
having no basis in physical science.
Alison Bernstein, a professor of
translational neuroscience at Michigan
State University said in an interview
with Vice that "You can't magically
make things happen. You can [However]
change the way you react to certain
situations, which sounds to me like
Cognitive Behavioral Therapy". She
want no to assert that "manifestation
is not supported by science.
Does paint and cardboard have joints in it
Calculate the velocity of an object.
moved around a circle with a radius of
1.65m and an acceleration of 3.5 rad /s²
Answer:
5.775 m/s
Explanation:
radial acceleration = velocity / radius
=> velocity = radial acceleration * radius
=> v = 3.5 * 1.65 = 5.775 (m/s)
According to Newton's 2nd Law of Motion, if the mass of an object is 10 kg and the force is 10 newtons, then the acceleration is
10 m/s/s
10 m/s
100 m/s/s
1 m/s/s
According to Newton's second Law of motion, if the mass of an object is 10 kg and the force is 10 newtons, then the acceleration is 1m/s².
How to calculate acceleration?The acceleration of a moving body can be calculated by dividing the force of the body by its mass.
According to this question, the mass of an object is 10 kg and the force is 10 newtons, then the acceleration can be calculated as follows:
acceleration = 10N ÷ 10kg
acceleration = 1m/s²
Therefore, according to Newton's second Law of motion, if the mass of an object is 10 kg and the force is 10 newtons, then the acceleration is 1m/s².
Learn more about acceleration at: https://brainly.com/question/12550364
#SPJ1
it is a routine composed of yells and cheers gymnastic skill and dance
Cheer dance is a routine composed of yells and cheers gymnastic skill and dance.
What is cheer dance?Cheer dance or cheerleading is a group activity used to entertain fans at athletic events and inspire louder, more enthusiastic cheering. It combines dancing and acrobatic aspects with shouted phrases.
A never-ending range of diverse stunts, jumps, pyramids, dances, and chants that integrate a variety of different movements can be included in the immensely complex sport of cheerleading. Base, partner, and spotter are the three primary cheerleading roles. These roles are all a part of cheerleading stunts, which pose the greatest risk of harm to participants.
It is a competitive sport and leisure activity made up of a set routine with necessary performance components, much like in gymnastics and dance. Additionally, it hopes to get the crowds to cheer in team sports event.
Learn more about cheer dance, refer the link:
https://brainly.com/question/29788167
#SPJ2
Your question is incomplete, but most probably your full question was:
1. It is a routine composed of yells and cheers, gymnastic skills and dance.
A. Contemporary dance
B. Hip-hop dance
C. Street dance
D. Cheer dance
.89m/s A vehicle that starts to move from the rest gets an acceleration of 5m/s² within 2 seconds. Calculate the velocity and distance covered by the vehicle within the given time. [Ans: 10m/s, 10m]
Explanation:
s = ? u = 0m/s v = ? a = 5m/s² t = 2s
v = u + at
= 0 + (5 x 2)
= 10 m/s
s = ut + 1/2 at²
= (0)(2) + x [tex]\frac{1}{2}[/tex] x 5 x 2²
= 10 m
Hope this helps!