Suppose a=3i-2j+k b=-i-4j+3k and c is avector lying along positive x axis with the property that a(b+c)=0 then find c?

Answer: C. Be more dense and flow under warm air.

Explanation:

think of a supermarket selling dairy products and when you open the fridge to get the milk, outside the supermarket is hot and inside the fridge is cold ice.

The energy-level change occurs as the atom is absorbs a 2.03-eV photon.

The energy change of the mercury atom is calculated as follows;

Energy emitted by a photon when it falls from level b to energy level e is calculated as follows;

ΔE = -3.71 eV - (-5.74 eV)

ΔE =  -3.71 eV + 5.74 eV

ΔE = 2.03 eV

When electron jumps from  lower energy level to higher energy level, energy is absorbed, thus, the energy-level change occurs as the atom is absorbs a 2.03-eV photon.

Learn more about energy level here: https://brainly.com/question/14287666

#SPJ1

The time it would take a 2500 W electric kettle to boil away 1.5 Kg of water is 2400 seconds

Use the formula:

Power × time = mass × specific heat

Given mass = 1. 5kg

Specific latent heat of vaporization = 4000000 J/ Kg

Power = 2500 W

Substitute the values into the formula

Power × time = mass × specific heat

2500 × time = 1. 5 × 4000000

Make 'time' the subject

time = 1. 5 × 4000000 ÷ 2500 = 6000000 ÷ 2500 = 2400 seconds

Therefore, the time it would take a 2500 W electric kettle to boil away 1.5 Kg of water is 2400 seconds.

Learn more about specific latent heat of vaporization:

https://brainly.in/question/1580957

#SPJ1

The reactance of the circuit will be 5.233×10⁻⁴ ohm. Inductive reactance is the product of 2 times π frequency and the coil inductance.

When alternating electricity passes through pure reactance, it causes a voltage drop that is 90 degrees out of phase with the current.

The letter “X” is used to represent reactance in mathematics, and it is measured in ohms.

The inductive reactance of a coil is calculated using the following formula:

Inductive reactance, or XL, is the product of 2 times p (pi), and the frequency of the ac current in hertz, and the coil inductance in henries.

XL= 2πfL

Where,

f {frequency)

L (Inductance)

The reactance of the circuit is found as;

[tex]\rm R_{new}=0.38[{(\frac{1}{60} )^2][/tex]

[tex]\rm R_{new}=1.055 \times 10^{-4} \ ohm[/tex]

The inductance of the circuit is;

[tex]\rm X_{new}=1.9(\frac{1}{60} )^2\\\\X_{new}= 5.233 \times 10^{-4}\ ohm[/tex]

Hence, the reactance of the circuit will be 5.233×10⁻⁴ ohm.

To learn more about the reactance, refer to the link;

https://brainly.com/question/17129912

#SPJ4

Answer:

False

Explanation:

It is actually I = V/R and V = I × R

The net force needed to lift a full grocery sack uniformly is 32.115 N.

When two or more forces are acting on the system of objects, then the to attain equilibrium, net force must be zero.

Given the weight of sack W = 210N and the acceleration a = 1.5m/s².

The mass of the sack will be

m = Weight / acceleration due to gravity

m = 210 N/9.81 m/s²

m = 21.41 kg

Using Newton's second law, the net force will be

F = mass x acceleration

F= 21.41 x 1.5

F = 32.115 N

Thus, the net force is 32.115 N.

Learn more about net force.

https://brainly.com/question/18031889

#SPJ1

Diagonal of cardboard=displacement to hole

So displacement till edge

Total distance

From centre to hole displacement

From the calculation, Sheila’s velocity immediately after she is thrown from the bike is 5.7 m/s.

Momentum is the product of mass and velocity. We know that the momentum before collision is equal to the momentum after collision.

Hence;

Momentum before collision = 340 kg • m/s.

Momentum after collision = 60v

Thus;

340 kg • m/s = 60v  kg • m/s

v = 340 kg • m/s/60 Kg

v = 5.7 m/s

Learn more about momentum:https://brainly.com/question/24030570

#SPJ1

#21

According to first equation of kinematics

#22

#a

The order is

#b

for speed find absolute velocity

So order is

S1<S3<S2

Answer:

See below ~

Explanation:

Question 21 :

⇒ v = u + at

⇒ v = 5 + 1.3 (2)

⇒ v = 5 + 2.6

⇒ v = 7.6 m/s

=============================================================

Question 22 : At t = 3

Subpart (a)

⇒ Object 1 : v = 2 + 3(3) = 11 m/s

⇒ Object 2 : v = -8 - 4(3) = -20 m/s

⇒ Object 3 : v = 1 - 5(3) = -14 m/s

⇒ Hence, their velocities are in the order : Object 2 < Object 3 < Object 1

Subpart (b)

⇒ Object 1 : v = | 2 + 3(3) | = 11 m/s

⇒ Object 2 : v = | -8 - 4(3) | = 20 m/s

⇒ Object 3 : v = | 1 - 5(3) | = 14 m/s

⇒ Hence, their speeds are in the order : Object 1 < Object 3 < Object 2

The statement indicating that 'Gravitation always does negative work' is FALSE.

Gravitation is a fundamental physical force that makes objects attract each other in the Universe.

This force (Gravitation) is required to maintain both constant positions and movement of objects.

In conclusion, the statement indicating that 'Gravitation always does negative work' is FALSE.

Learn more about Gravitation here:

https://brainly.com/question/557206

#SPJ1

Answer:false

Explanation:

Answer:

83000kg

Explanation:

mass=8300kg

g=10

w=mg

8300×10=83000kg

Maria throws two stones from the top edge of a building at a speed of 20 m/s, The time is mathematically given as

t=4.5 sec.

Generally, the equation for speed  is mathematically given as

V = u+at

Therefore

0 = 22-9.8xt.

t = 22 /9.8 sec

t = 2.24489.

The same time will be taken from max^m height to point O

The extra time is taken

t=4.49 sec.

t=4.5 sec.

Read more about Time

https://brainly.com/question/4931057

#SPJ1

Sian wants to count the number of seconds it takes for a beaker's contents to become purple from clear. She should utilize a stopwatch as her instrument for this job.

Watch that, when turned on and off, measures the amount of time that has passed since a specific time.

Sian wants to measure the number of seconds that it takes for the contents of a beaker to change from clear to purple. Stopwatch is the tool she should utilize for this purpose.

Hence, option B is correct.

To learn more about the stopwatch refer;

https://brainly.com/question/13758413

#SPJ1

Answer: Sian wants to count the number of seconds it takes for a beaker's contents to become purple from clear. She should utilize a stopwatch as her instrument for this job.

option b

Explanation:

Answer:

3.2 [tex]10^{-2} ohm^{-1} m^{-1}[/tex]

Explanation:

Resistance=5 ohm

Length=4m

Cross sectional area=2.5 x 10

Conductivity = 1/ resistivity

                      =[tex]\frac{length}{resistance x cross sectional area}[/tex]

Conductivity=4 /5 x 2.5 x 10

Conductivity=4/125

Conductivity=3.2x[tex]10^{-2}[/tex][tex]ohm^{-1} m^{-1}[/tex]

Answer:

Explanation:

1800x0.9=1620kg

Answer:

4.0208 x 10^16 meters

Explanation:

speed of light in m/s   *      # seconds in a year      * 4.25 years =

2.99792 x 10^8   *        3600*24*365.25  *     4.25 = 4.0208 x 10^16 m

Explanation:

Force = mass x acceleration

F= ma (formula)

15N = o.5kg x a

Divide both sides by o.5

a = 30 (greater acceleration)

15N = 4.5kg x a

Divide both sides by 4.5

a= 3.33 (great acceleration)

15N = 0.05kg x a

Divide both sides by 0.05

a = 300 (greatest acceleration)

The cross-sectional area of the tape is determined as 3.9 x 10⁻⁵ ft².

The volume of the tape is calculated as follows;

volume = mass/density

volume = (1.95 lb)/(490 lb/ft³)

volume = 3.98 x 10⁻³ ft³

V  = AL

A = V/L

A = 3.98 x 10⁻³ ft³/102 ft

A = 3.9 x 10⁻⁵ ft²

Thus, the cross-sectional area of the tape is determined as 3.9 x 10⁻⁵ ft².

Learn more about area here: https://brainly.com/question/3948796

#SPJ1

The frequency of an electromagnetic wave with wavelength of 10nm will be 3 × 10∧7 Hz and would belong to the X-ray or ultraviolet part of the electromagnetic spectrum due to its wavelength

What is frequency?

Frequency is defined as the number of oscillations of a wave per unit time and is measured in hertz(Hz).

It is also inversely proportional to the wavelength.

The frequency of an electromagnetic wave can be calculated using the formula;

frequency = velocity of light divided by the wavelength

f = v ÷ λ

Note that the velocity of light = 3 × 10 ∧8 m/s

Wavelength = 10nm

Frequency, f = 3 × 10∧8 ÷ 10 = 3 × 10∧7 Hz

Hence, the frequency of an electromagnetic wave with wavelength of 10nm will be 3 × 10∧7 Hz and would belong to the X-ray or ultraviolet part of the electromagnetic spectrum due to its wavelength.

Learn more about electromagnetic spectrum here:

https://brainly.com/question/13803241

#SPJ1

From the information provided and the calculations, the energy of the drop is 1.51 eV

The Rydberg formula is used to obtain the energy of a photon or the wavelength of a photon.

Thus;

1/λ = 1.097 * 10^7 (1/3^2 - 1/5^2)

1/λ = 1.097 * 10^7(0.11 - 0.04)

λ = 1.3 * 10^-6 m

Since;

E = hc/λ

E = 6.6 * 10^-34 * 3 * 10^8/1.3 * 10^-6

E = 1.51 * 10^-19 J or 1.51 eV

Learn more about photon:https://brainly.com/question/20912241

#SPJ1

Answer:

0.97eV

Explanation:

The energy emitted during n=5 is 0.54 eV

The energy emitted during n=3 is 1.51 eV
(This information is on the Physics Reference Table 2006 edition)

We find the change in the energy level which is:  

1.51eV-0.54eV = 0.97eV

Therefore the energy emitted by the photon is 0.97eV.

The magnitude of the angular acceleration of the magnetic disk is determined as 35 rad/s².

The angular acceleration of the disk is determined from the principle of conservation of angular momentum as follows;

τ = Iα

where;

α is angular acceleration

I is moment of inertia of the disk

I = 0.5MR²

I = 0.5 x 0.2 x 2²

I = 0.4 kgm²

τ = Iα

α = τ/I

α = (14)/(0.4)

α = 35 rad/s²

Learn more about angular acceleration here: https://brainly.com/question/21278452

#SPJ1

Answer:

Approximately [tex](-348\; {\rm J})[/tex], assuming that the bike was on level ground.

Explanation:

If an object of mass [tex]m[/tex] is moving at a speed of [tex]v[/tex], the kinetic energy of that object would be [tex](1/2)\, m\, v^{2}[/tex].

At a speed of [tex]v = 3.84\; {\rm m\cdot s^{-1}}[/tex], the kinetic energy of the bike and the cyclist- combined- would be:

[tex]\begin{aligned} &\frac{1}{2}\, m\, v^{2} \\=\; &\frac{1}{2}\times 53.0\; {\rm kg} \times (3.84\; {\rm m\cdot s^{-2}})^{2} \\ \approx \; & 390.76\; {\rm J}\end{aligned}[/tex].

At a speed of [tex]v = 1.27\; {\rm m\cdot s^{-1}}[/tex], the kinetic energy of the bike and the cyclist- combined- would be:

[tex]\begin{aligned} &\frac{1}{2}\, m\, v^{2} \\=\; &\frac{1}{2}\times 53.0\; {\rm kg} \times (1.27\; {\rm m\cdot s^{-2}})^{2} \\ \approx \; &42.741 \; {\rm J}\end{aligned}[/tex].

The energy change was approximately:

[tex]390.76\; {\rm J} - 42.741\; {\rm J} \approx 348\; {\rm J}[/tex].

If the bike was on level ground, the friction on the bike and the cyclist would have done a work of [tex](-348\: {\rm J})[/tex] to reduce the kinetic energy of the bike and the cyclist by that amount.

Answer: C) -348J

Explanation:

42.741 - 390.76 (the kinetic energy of the two speeds) is equal to -348.

Answer:

Displacement...

Explanation:

Displacement is a vector quantity as it have both magnitude and direction...

[tex]...[/tex]

a. displacement is the correct answer

Displacement is a vector quantity

Displacement is a vector quantity because it has both magnitude and direction.

Answer:

K=6.250 J

Explanation:

m=500kg

v=m/s

Kinetic energy= ½mv²=½(500×25) J= 6.250 J

If the man DECREASES the force of his push on the cart, the cart slows down.

The force applied to an object is determined by applying Newton's second law of motion.

F = ma

where;

a = Δv/t

F = (mΔv)/t

mΔv = Ft

Δv = Ft/m

From the equation above, when the applied force decreases, the change in velocity decreases.

Thus, if the man DECREASES the force of his push on the cart, the cart slows down.

Learn more about force here: https://brainly.com/question/12970081

#SPJ1

The diagram is labelled to DRAW the RESULTANT wave and LABEL the areas of interference with CI, DI and/or points of TDI.

When a light ray falls on the interface of two medium like air and water, then the portion of light is reflected and another portion of the light is refracted into the water medium. The angle of incidence is equal to the angle of reflection but the angle of incidence is larger then the angle of refraction.

Open the attached file. It shows 2 waves (a blue one and an orange one) that are moving through the same medium at the same time.

Thus, the diagram is labelled.

Learn more about refraction.

https://brainly.com/question/14760207

#SPJ1

The direction of a vector that has the following components is 233°.

The direction of a vector is where its endpoint points. However, when at least one of the characteristics mentioned above is different, we say that the vectors are different.

In this case, this calculus will be:

[tex]tan\theta= \frac{59}{44} \\\theta= tan^{-1}(\frac{59}{44})\\ \theta= 233\°[/tex]

See more about vectors at brainly.com/question/13322477

#SPJ1

The vector with components x = -44 m and y = -59 m has a direction of approximately 52.16 degrees counterclockwise from the positive x-axis.

The direction of a vector with components x = -44 m and y = -59 m can be determined using trigonometry.  In this case, we have:

x-component (x) = -44 m

y-component (y) = -59 m

We can use the inverse tangent function to find the angle.

The direction angle (θ) can be calculated as:

θ = arctan(y / x)

θ = arctan((-59 m) / (-44 m))

Calculating this expression:

θ ≈ arctan(1.341)

To find the actual angle, we can use a calculator or table to determine the inverse tangent of 1.341.

θ ≈ 52.16 degrees

Therefore, the direction of the vector is approximately 52.16 degrees in the counterclockwise direction from the positive x-axis.

The vector with components x = -44 m and y = -59 m has a direction of approximately 52.16 degrees counterclockwise from the positive x-axis.

To know more about Direction, visit

brainly.com/question/30817683

#SPJ11

Cheer dance​ is a routine composed of yells and cheers gymnastic skill and dance.  

Cheer dance or cheerleading is a group activity used to entertain fans at athletic events and inspire louder, more enthusiastic cheering. It combines dancing and acrobatic aspects with shouted phrases.

A never-ending range of diverse stunts, jumps, pyramids, dances, and chants that integrate a variety of different movements can be included in the immensely complex sport of cheerleading. Base, partner, and spotter are the three primary cheerleading roles. These roles are all a part of cheerleading stunts, which pose the greatest risk of harm to participants.

It is a competitive sport and leisure activity made up of a set routine with necessary performance components, much like in gymnastics and dance. Additionally, it hopes to get the crowds to cheer in team sports event.

Learn more about cheer dance, refer the link:

https://brainly.com/question/29788167

#SPJ2

Your question is incomplete, but most probably your full question was:

1. It is a routine composed of yells and cheers, gymnastic skills and dance.

A. Contemporary dance

B. Hip-hop dance

C. Street dance

D. Cheer dance​