Answer:
d. The company uses role-based access control and her user account hasn't been migrated into the correct group(s) yet
Explanation:
Since Deidre is accessing her e-mail there appears to be nothing wrong with her account or password. Since her role is new, most likely the problem is associated with her new role.
1) (30 pts ) Oxygen (O2) flows through a pipe, entering at at 4 m/sec at 10000 kPa, 227oC. For a pipe inside diameter of 3.0 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas
Complete Question
Nitrogen (N2) flows through a pipe, entering at at 4 m/sec at 1000 kPa, 2270C. For a pipe inside diameter of 3 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas Then using your ideal gas mass flow rate find the rate at which enthalpy enters the pipe (kJ/sec) NO Cp, Cv, k permitted
Answer:
[tex]H=9.91kJ/sec[/tex]
Explanation:
From the question we are told that:
Velocity [tex]v=4 m/sec[/tex]
Pressure [tex]P=1000kPa[/tex]
Temperature [tex]T=227 \textdegree C[/tex]
Diameter [tex]d=3cm=>0.03m[/tex]
Generally the equation for volumetric Flow Rate is mathematically given by
[tex]V_r=(\frac{\pi*d^2}{4}v)[/tex]
[tex]V_r=(\frac{\pi*(0.03)^2}{4} *4)[/tex]
[tex]V_r=0.002827m^3/s[/tex]
Generally the equation for mass Flow Rate is mathematically given by
[tex]m_r=\frac{PV_r}{RT}[/tex]
[tex]m_r=\frac{1000*0.002827}{0.297*(227+273)}[/tex]
[tex]m_r=0.019kg/sec[/tex]
Generally the equation for mass Flow Rate is mathematically given by
Using gas Table for enthalpy Value
[tex]T=500K=>h=520.75kg[/tex]
Therefore
[tex]H=mh[/tex]
[tex]H=0.019*520.75[/tex]
[tex]H=9.91kJ/sec[/tex]
Cho biết tác dụng chung của các hệ giằng khung ngang nhà công nghiệp nhẹ 1 tầng 1 nhịp.
The secondary coil of a step-up transformer provides the voltage that operates an electrostatic air filter. The turns ratio of the transformer is 41:1. The primary coil is plugged into a standard 120-V outlet. The current in the secondary coil is 1.2 x 10-3 A. Find the power consumed by the air filter.
Answer:
5.9 watts
Explanation:
The secondary voltage is the primary voltage multiplied by the turns ratio:
(120 V)(41) = 4920 V
The power is the product of voltage and current:
(4920 V)(1.2·10^-3 A) = (4.92)(1.2) W = 5.904 W
The power consumed is about 5.9 watts.
Explain the 11 sections that a typical bill of quantity is divided into
Answer:
The main sections included in the bill of quantities are Form of Tender, Information, Requirements, Pricing schedule, Provisional sums, and Day works.
Functional and nonfunctional requirements documents are used to _____.
define the financial budget of a system
define the purpose of a system
facilitate communication between the users and a system
help exercise control over the inner workings of the firm.
Answer:
Non-functional requirements when defined and executed well will help to make the system easy to use and enhance the performance
Explanation:
what the different methods to turn on thyrister and how can a thyrister turned off
Answer:
forward voltage triggering
temperature triggering
dv/dt triggering
light triggering
gate triggering
Then turning off;
Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals
Explanation:
hope it helps
When exchanging information with anyone involved in the collision, you should _____.
Try to be as relax as possible.
Provide names of all parties involved.
Provide vehicle information and identification details.
Provide full names, address, registration numbers and insurance company details.
Explanation:
After a collision one may be confused, afraid and have no attention about the details that what happened because all the collision event happens in a short interval of time. So the first thing one should do during information exchange is to sit back and relax and be calm so that one can remind the things at some extent. After that provide all the details about injured people and the involved vehicles.
The following laboratory test results for Atterberg limits and sieve-analysis were obtained for an inorganic soil. [6 points] Sieve analysis Sieve Size No. 4 (4.75 mm) No. 10 (2.00 mm) No. 40 (0.425 mm) No. 200 (0.075 mm) Percent passing by weight 80 60 30 10 Atterberg limits Liquid limit (LL) Plastic limit (PL 31 25
(a) Classify this soil according to USCS system, providing the group symbol for it. Show how you arrive at the final classification.
(b) According to USCS system, what is a group name for this soil?
(c) Is this a clean sand? If not, explain why.
Answer: hello the complete question is attached below
answer:
A) Group symbol = SW
B) Group name = well graded sand , fine to coarse sand
C) It is not a clean sand given that ≤ 50% particles are retained on No 200
Explanation:
A) Classifying the soil according to USCS system
( using 2nd image attached below )
description of sand :
The soil is a coarse sand since ≤ 50% particles are retained on No 200 sieve, also
The soil is a sand given that more than 50% particles passed from No 4 sieve
The soil can be a clean sand given that fines ≤ 12%
The soil can be said to be a well graded sand because the percentage of particles passing through decreases gradually over time
Group symbol as per the 2nd image attached below = SW
B) Group name = well graded sand , fine to coarse sand
C) It is not a clean sand given that ≤ 50% particles are retained on No 200
A O.1m³ rigid tank contains steam initially as 500k pa and 200°C. The steam is now allowed to cool until the temperature drops to 50°C. Determine the amount of heat transfer during the process and the final pressure in the tank
Answer:
Check it out here
Explanation:
A resistor has code 104 printed on it .What is the resistive value of this resistor
Answer:
X = 1 (1st digit in the code)
Y = 0 (2nd digit)
Z = 4 (3rd multiplier digit)
104 → 10 × 10^4 Ω
→ 10 × 10000Ω
→ 100 kΩ
resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).
Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.
When we use numbers, let's assume that we have 3 single-digit numbers abc.
So if the code in our resistor is abc, this will mean that the resistance of the resistor is:
ab×10^c Ω
Using this general rule we can see that if the code is 104, then the resistance will be:
r = 10×10^4 Ω
= 100,000 Ω
Then we can conclude that the resistive value of this resistor is 100,000 Ω
If you want to learn more, you can read:
https://brainly.com/question/74415
Magnetic particle testing can be done only on metals that can be magnetized.
True or false
A 2-stage dcv that has an internal pilot does not work well (if at all) on
Answer:
i really font onow why tbh eot you
what is the best book for mechanic of materials?
Answer:
As per my experience Egor Popov is one the best book for mechanics of materials.
Explanation:
hope this helps
The impeller shaft of a fluid agitator transmits 20 kW at 430 rpm. If the allowable shear stress in the impeller shaft must be limited to 65 MPa, determine (a) the minimum diameter required for a solid impeller shaft. (b) the maximum inside diameter permitted for a hollow impeller shaft if the outside diameter is 36 mm. (c) the percent savings in weight realized if the hollow shaft is used instead of the solid shaft. (Hint: The weight of a shaft is proportional to its cross-sectional area.)
Given :
Power, P = 20 kW
Speed, N = 430 rpm
Allowable shear stress, τ = 65 MPa
Torque in the shaft is given by :
[tex]$P=\frac{2 \pi NT}{60}$[/tex]
[tex]$T=\frac{60 \times 20 \times 10^3}{2 \pi \times 430}$[/tex]
T = 444.37 N.m
Diameter of the solid shaft is
[tex]$d=\sqrt[3]{\frac{16 T}{\pi \tau}}[/tex]
[tex]$d=\sqrt[3]{\frac{16 \times 444.37}{3.14 \times 65}}[/tex]
[tex]$d=\sqrt[3]{34.83} $[/tex]
d = 3.265 m
d = 326.5 mm
Internal diameter of the hollow shaft is :
[tex]$\frac{T}{\frac{\pi}{32} \left( d_0^4 - d_i^4 \right)}=\frac{\tau}{d_0/2}$[/tex]
[tex]$\frac{444.37}{\frac{3.14}{32} \left( 0.036^4 - d_i^4 \right)}=\frac{65 \times 10^6}{0.036/2}$[/tex]
[tex]$\frac{444.37}{0.09 \left( 1.6 \times 10^{-6} - d_i^4 \right)}=\frac{65 \times 10^6}{0.018}$[/tex]
[tex]$\frac{7.99}{ \left( 1.6 \times 10^{-6} - d_i^4 \right)}=5850000$[/tex]
[tex]$1.3\times 10^{-6} = 1.6 \times 10^{-6} - d_i^4 \right)}$[/tex]
[tex]$d_i^4=300000$[/tex]
[tex]$d_i = 23.40$[/tex] mm
Percentage savings in the weight is given by :
Percentage saving = [tex]$\frac{W_{solid}-W_{hollow}}{W_{solid}}\times100$[/tex]
[tex]$=\frac{V_{solid}-V_{hollow}}{V_{solid}}\times100$[/tex]
[tex]$=\frac{d^2 - (d_0^2 - d_i^2)}{d^2} \times 100$[/tex]
[tex]$=\frac{(326.5)^2 - (0.036^2 - (32.40)^2)}{(326.5)^2} \times 100$[/tex]
[tex]$=\frac{106602 - \left(1.29 \times 10^{-3} - 1049.76 \right)}{106602} \times 100$[/tex]
[tex]$=\frac{106602 - 1049 }{106602} \times 100$[/tex]
[tex]$=\frac{105553 }{106602} \times 100$[/tex]
= 99.01 %
what does mean setbacks with MRT station?
An incompressible viscous fluid flows through a pipe with a flow rate of 1 mL/s. The pipe has a uniform diameter D0 and a length L0. A pressure difference of P0 between the ends of the pipe is required to maintain the flow rate. What would be the flow rate if the pressure difference was increased to 2P0 and the diameter was increased to 2D0
Answer:
[tex]Q_2 = 32[/tex] mL/s
Explanation:
Given :
The flow is incompressible viscous flow.
The initial flow rate, [tex]Q_1[/tex] = 1 mL/s
Initial diameter, [tex]D_1= D_0[/tex]
Initial length, [tex]L_1=L_0[/tex]
The initial pressure difference to maintain the flow, [tex]P_1=P_0[/tex]
We know for a viscous flow,
[tex]$\Delta P = \frac{32 \mu V L}{D^2}$[/tex]
[tex]$\Delta P = \frac{32 \mu Q L}{\frac{\pi}{4}D^4}$[/tex]
[tex]$Q \propto \Delta P \times D^4$[/tex]
[tex]$\frac{Q_1}{Q_2}= \frac{P_1}{P_2} \times \left( \frac{D_1}{D_2} \right)^4$[/tex]
[tex]$\frac{1}{Q_2}= \frac{P_0}{2P_0} \times \left( \frac{D_0}{2D_0} \right)^4$[/tex]
[tex]$\frac{1}{Q_2}= \frac{1}{2} \times \left( \frac{1}{2} \right)^4$[/tex]
[tex]$\frac{1}{Q_2}= \frac{1}{32}$[/tex]
∴ [tex]Q_2 = 32[/tex] mL/s
The flow rate if the pressure difference was increased to 2P0 and the diameter was increased to 2D0 is; Q2 = 32 mL/s
We are given;
Initial flow rate; Q1 = 1 mL/s
Initial uniform diameter; D0
Initial Length; L0
Initial Pressure difference; P0
Relationship between pressure, flow rate and diameter for vicious flow is given by;
Q1/Q2 = (P1/P2) × (D1/D2)⁴
Where;
Q1 is initial flow rate
Q2 is final flow rate
P1 is initial pressure difference
P2 is final pressure difference
D1 is initial diameter
D2 is final diameter
We are told that the pressure difference was increased to 2P0 and the diameter was increased to 2D0. Thus;
P2 = 2P0
D2 = 2D0
Thus;
1/Q2 = (P0/2P0) × (D0/2D0)⁴
>> 1/Q2 = ½ × (½)⁴
1/Q2 = 1/32
Q2 = 32 mL/s
Read more about vicious flow at; https://brainly.com/question/2684299
True or false: You can create a network with two computers.
Answer
True
Rafel knows that lessons learned is a valuable aid to future projects. When should he and his team address
lessons learned on a project?
Select an answer:
Add lessons learned as a topic in status meetings
Review past lessons learned so a new one does not have to be created,
Create lessons learned at the end of the project.
Brainstorm lessons learned at the beginning of a project
Answer: Create lessons learned at the end of the project.
Explanation:
Lessons learned are the experiences that are gotten from a project which should be taken into account for the future projects. Lesson learned are created at the end of the project.
The main objective of the lessons learned is that they show both the positive experience and the negative experience of a project and this will help the future projects that will be undertaken.
Which statement describes the relay between minerals and rocks ?
Answer:
•○●□■hey hi!■□●○•Explanation:
Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.
☆♡hope this helps♡☆Question in Statistics and Probability 2
Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
State the Null and the Alternative Hypotheses.
I want to explain what 2000 feet looks like to young children so that they can imagine it in class
Answer:
maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."
Explanation:
sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.
hỗ trợ mình với được không các bạn
Answer:
Explanation:
Be bop
A recessed luminaire bears no marking indicating that it is ""Identified for Through- Wiring."" Is it permitted to run branch-circuit conductors other than the conductors that supply the luminaire through the integral junction box on the luminaire?
Answer:
No it is not permitted
Explanation:
It is not permitted because as per NEC 410.21 policy no other conductor is allowed to be passed through integral junction box luminaries unless such conductor supply recessed luminaries.
The marking will show that the Luminaries is of the right construction or right installation to ensure that the the conductors ( in the outer boxes ) will not be exposed to temperatures greater than the conductor rating, hence the lack of marking makes it not to be permitted.
Which of the following conditions were present in over 80% of paddling fatalities from 1995-2000?
Answer:
80% of the people that were killed weren't wearing a safety flotation device ( in correct terminology Personal Flotation Device, or PFD )
Explanation:
Hence they drowned due to the lack of safety.
The condition present in over 80% of paddling fatalities is that the victims were said to be not wearing a personal flotation device (PFD).
What is paddling in the sea?The act of paddling is known to be a sport or something one can do for fun or for games.
Conclusively, a lot of paddling fatalities 1995-2000 was due to the fact that the people who were engage in the sport or act were not putting on a personal flotation device (PFD) and this can lead to death or drowning.
Learn more about paddling fatalities from
https://brainly.com/question/3787626
A 40kg steel casting (Cp=0.5kJkg-1K-1) at a temperature of 4500C is quenched in 150kg of oil (Cp=2.5kJkg-1K-1) at 250C. If there are no heat losses, what is the change in entropy of?
(i) The casing.
(ii) The oil.
(iii) Both considered.
If the constant is added to every observation of data then arithmatic mean obtained is
Answer:
Explanation:
Increased by the constant. Take a very simple case.
4 + 5 + 6 = 15
The mean is 5 (obtained by dividing the total (15) by the number of terms (3).
Now add a constant say 6
4 + 6 = 10
5 + 6 = 11
6 + 6 = 12
Total = 33/3 = 11
So the mean 5 is increased by the constant 6.
Now do the same thing more symbolically.
4 + c
5 + c
6 + c
Total = 15 + 3c
Divide by 3 you get 5 + c
If you want a more formal proof involving n terms, leave a note.
A steel component with ultimate tensile strength of 800 MPa and plane strain fracture toughness of 20 MPam is known to contain a tunnel (internal) crack of length 1.4 mm. This alloy is being considered for use in a cyclic loading application for which the design stresses vary from 0 to 410 MPa. Would you recommend this alloy for this application
Complete question:
A steel component with a tensile strength of 800 MPa and fracture toughness Kic=20 MPa Nm is known to contain internal cracks (also called tunnel cracks) with the maximum length of 1.4 mm. This steel is being considered for use in a cyclic loading application for which the designed stresses vary from 0 to 420 MPa. Would you recommend using this steel in this application?
a. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.
b. Yes, this because the tensile strength of steel is much higher than the applied highest stress of 420 MPa.
c. Yes, this because the calculated critical stress to fracture for the cracks is higher than the highest applied stress of 420 MPa and the steel can withstand the stress of 420 MPa.
d. No. Although the calculated critical stress to fracture for the cracks is slightly higher than the highest applied stress of 420 MPa and the steel may withstand the static stress of 420 MPa, the cyclic loading may cause rapid fatigue fracture.
Answer:
A. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.
Explanation:
we are not sure if to recommend this alloy for this application given that this material has already been left to experience fatigue degradation. the cyclic load application brings about a growth in the crack. We know that cyclic loading is continuous loading that is useful for the testing of fatigue. Therefore the answer to this question is option a. We cannot make recommendations except fatigue testing has been carried out.
thank you!
what is tracer lathe machine
Answer: The tracer lathe is a roughing operation for the output shaft on rear wheel drive transmissions.
Explanation:
When the rod is circular, radial lines remain straight and sections perpendicular to the axis do not warp. In this case, the strains vary linearly along radial lines. Within the proportional limit, the stress also varies linearly along radial lines. If point A is located 12 mm from the center of the rod, what is the magnitude of the shear stress at that point
The question is incomplete. The complete question is :
The solid rod shown is fixed to a wall, and a torque T = 85N?m is applied to the end of the rod. The diameter of the rod is 46mm .
When the rod is circular, radial lines remain straight and sections perpendicular to the axis do not warp. In this case, the strains vary linearly along radial lines. Within the proportional limit, the stress also varies linearly along radial lines. If point A is located 12 mm from the center of the rod, what is the magnitude of the shear stress at that point?
Solution :
Given data :
Diameter of the rod : 46 mm
Torque, T = 85 Nm
The polar moment of inertia of the shaft is given by :
[tex]$J=\frac{\pi}{32}d^4$[/tex]
[tex]$J=\frac{\pi}{32}\times (46)^4$[/tex]
J = 207.6 [tex]mm^4[/tex]
So the shear stress at point A is :
[tex]$\tau_A =\frac{Tc_A}{J}$[/tex]
[tex]$\tau_A =\frac{85 \times 10^3\times 12 }{207.6}$[/tex]
[tex]$\tau_A = 4913.29 \ MPa$[/tex]
Therefore, the magnitude of the shear stress at point A is 4913.29 MPa.
Tech A says that when performing a cylinder leakage test, the piston should be positioned at bottom dead center. Tech B says that a blown head gasket would generally leak past the exhaust valve. Who is correct
The causes of low compression in an engine cylinder and leakage past the exhaust can be identified by performing mechanical tests on the engine
The correct technician is Tech B; Blown head gasket would generally leak past the exhaust valve
The reason for arriving at the above selection is as follows:
A cylinder leakage test is generally performed after there is an indication of low compression from one or more cylinders. The test allows the identification of the part of the cylinder that is leaking.
The cylinder that shows sign of low compression is often the location that the cylinder leakage test is performed, although, the test can be performed on every cylinder
A cylinder leakage test is valid only when
The temperature of engine is about the temperature range of the engine in operationThe cylinder under test is at the Top Dead Center (TDC) position, such that the position of the piston in the cylinder is at the top or highest point of its strokeTherefore, the positioning of the piston in the bottom dead center during a leakage test as mentioned by Tech A is not correct
The route of coolant in the engine are sealed by the cylinder head gasket, where there is a blown head gasket, the coolant will be allowed to leak into the cylinders and into the exhaust, causing white smoke and sweet odor of antifreeze
Therefore, Tech B is correct, coolant leakage into the exhaust is an indication of a blown head gasket
Learn more about engine mechanical testing here:
https://brainly.com/question/14639903