A generator consists of 1000 turns of wire around a coil of area 10cm2 (0.0010m 2 ). Calculate the peak output voltage of this generator when operating at 100 cycles/second in a 0.50 tesla field.

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

Answer:

See attached file

Explanation:

Answer:

The glove takes 1.02s to return to the pitchers hand.

Explanation:

Given;

initial velocity the pitcher's glove, u = 5 m/s

Apply kinematic equation

s = ut - ¹/₂gt²

where;

g is acceleration due to gravity = 9.8 m/s²

t is the time takes the glove to return to the pitchers hand

s is the displacement of the glove, which will be equal to zero when the glove returns to the pitchers hand. (s = 0)

0 = ut - ¹/₂gt²

ut = ¹/₂gt²

u = ¹/₂gt

gt = 2u

t = (2u) / g

t = (2 x 5) / 9.8

t = 1.02 s

Therefore, the glove takes 1.02s to return to the pitchers hand.

Answer:A  200

Explanation:

Vp=1.41*Vrms

Vp=169.7 v

Z=Vp/Ip

Z=169.7/.8484

Z=200.03 ohm

Answer:

0 J

Explanation:

Since work done W = ∫F.dr and F(x, y, z)= z²i + 4xyj + 5y²k and dr = dxi + dyj + dzk

F.dr = (z²i + 4xyj + 5y²k).(dxi + dyj + dzk) = z²dx + 4xydy + 5y²dz

W = ∫F.dr = ∫z²dx + 4xydy + 5y²dz = z²x + 2xy² + 5y²z

We now evaluate the work done for the different regions

W₁ = work done from (0,0,0) to (1,0,0)

W₁ = {z²x + 2xy² + 5y²z}₀₀₀¹⁰⁰ = 0²(1) + 2(1)(0)² + 5(0)²(0) - [(0)²(0) + 2(0)(0)² + 5(0)²(0)] = 0 - 0 = 0 J

W₂ = work done from (1,0,0) to (1,5,1)

W₂ = {z²x + 2xy² + 5y²z}₁₀₀¹⁵¹ =   (1)²(1) + 2(1)(5)² + 5(5)²(1) - [0²(1) + 2(1)(0)² + 5(0)²(0)] =  1 + 50 + 125 - 0 = 176 J

W₃ = work done from (1,5,1) to (0,5,1)

W₃ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁵¹ =   1²(0) + 2(0)(5)² + 5(5)²(1) - [(1)²(1) + 2(1)(5)² + 5(5)²(1)]  = 125 - (1 + 50 + 125) = 125 - 176 = -51 J

W₄ = work done from (0,5,1) to (0,0,0)

W₄ = {z²x + 2xy² + 5y²z}₁₅₁⁰⁰⁰ =   (0)²(0) + 2(0)(0)² + 5(0)²(0) - [1²(0) + 2(0)(5)² + 5(5)²(1)] = 0 - 125 = -125 J

The total work done W is thus

W = W₁ + W₂ + W₃ + W₄

W = 0 J + 176 J - 51 J - 125 J

W = 176 J - 176 J

W = 0 J

The total work done equals 0 J

Answer:

Resistance of each bulb = 360 ohms

Explanation:

Let each bulb have a resistance r .

Since, even after removing one of the bulbs, the circuit is closed and the other bulbs glow. Therfore, the bulbs are connected in Parallel connection.

[tex] \frac{1}{r(equivalent)} = \frac{1}{r1} + \frac{1}{r2} + + + + \frac{1}{r15} [/tex]

[tex] \frac{1}{r(equivalent)} = \frac{15}{r} [/tex]

R(equivalent) = r/15

Now, As per Ohms Law :

V = I * R(equivalent)

120 V = 5 A * r/15

r = 360 ohms

Answer:

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil which will increase total induced electromotive force

Explanation:

galvanometer is an instrument that can detect and measure small current in an electrical circuit.

If the magnet is moved, the galvanometer needle will deflect, showing that current is flowing through the coil. If it is move in a way into the coil,the needle deflect in that way and if it move in another way, it will deflect in the other way.

The total induced emf is equal to the emf induced in each loop by the changing magnetic flux, then multiplied by the number of loops and an increase in the number of loops will cause increase in the total induced emf.

Answer:

The  value is  [tex]B = 0.0043 \ T[/tex]

Explanation:

From the question we are told that

   The  length of the solenoid is  [tex]l = 63.5 = 0.635 \ m[/tex]

    The number of turns is  [tex]N = 960 \ turns[/tex]

    The  current is  [tex]I = 2.28 \ A[/tex]

Generally the magnetic field is mathematically represented as

      [tex]B = \mu _o * n * I[/tex]

Where  n is the number of turn per unit length which is mathematically evaluated as

      [tex]n = \frac{N}{l}[/tex]

     [tex]n = \frac{960}{0.635}[/tex]

     [tex]n = 1512 \ turns /m[/tex]

and  [tex]\mu_o[/tex] is the permeability of free space with value  [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

So  

    [tex]B = 4\pi * 10^{-7} * 1512 * 2.28[/tex]

    [tex]B = 0.0043 \ T[/tex]

Complete Question

An emf is induced in a conducting loop of wire 1.12m long as its shape is.

changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.

Answer:

The induced emf is  [tex]\epsilon = 0.0863 \ V[/tex]

Explanation:

From the question we are told that

      The  time taken is  [tex]\Delta t = 0.125 \ s[/tex]

       The magnitude of the magnetic field is  B =  0.504 T

        The length of the loop wire is  [tex]l = 1.12 \ m[/tex]

Generally the circumference of the wire when in circular form is  

          [tex]C = 2 \pi r[/tex]

=>        [tex]l = 2 \pi r[/tex]

=>         [tex]r =[/tex][tex]\frac{l}{2 \pi}[/tex]

=>          [tex]r =[/tex][tex]\frac{1.12}{2 * 3.142}[/tex]

=>        [tex]r =[/tex][tex]0.1782 \ m[/tex]

Now the area of the wire as a circle is

           [tex]A = \pi r^2[/tex]

    =>     [tex]A = 3.142 * (0.1782)^2[/tex]      

     =>    [tex]A = 0.0998 \ m^2[/tex]

The  length of one side of the square is

         [tex]b = \frac{l}{4}[/tex]

         [tex]b = \frac{1.12}{4}[/tex]

         [tex]b = 0.28 \ m[/tex]

Now the area of the wire as a square is

          [tex]A_s = b^2[/tex]

=>          [tex]A_s =(0.28 )^2[/tex]

             [tex]A_s = 0.0784 \ m^2[/tex]

Generally the induced emf is mathematically represented as

        [tex]\epsilon = \frac{B * [A - A_s ]}{\Delta t }[/tex]

=>      [tex]\epsilon = \frac{0.504 * [0.0998 - 0.0784 ]}{0.125 }[/tex]

=>      [tex]\epsilon = 0.0863 \ V[/tex]

Answer:

Explanation:

The Force experienced by the wire in the uniform magnetic field is expressed as F = BILsin∝ where;

B is the magnetic field (in Tesla)

I is the current (in amperes)

L is the length of the wire (in meters)

∝ is the angle that the conductor makes with the magnetic field.

Given parameters

L = 0.56 m

I = 2.6A

F = 0.24N

∝  = 90°

Required

magnitude of the magnetic field (B)

Substituting the given values into the formula given above we will have;

F = BILsin∝

0.24 = B * 2.6 * 0.56 sin90°

0.24 =  B * 2.6 * 0.56 (1)

0.24 = 1.456B

1.456B = 0.24

Dividing both sides by 1.456 will give;

1.456B/1.456 = 0.24/1.456

B ≈ 0.165Tesla

Hence the magnitude of the magnetic field is approximately 0.165Tesla

Answer:

a) for the torque to be maximum, sin should be maximum

i.e (sinФ)maximum = 1

b) therefore the Maximum torque is

Tmax = 0.1838 × 1 = 0.1838  N.m

c) Given the torque is 71.0% of its maximum value; Ф  = 45.24⁰ ≈ 45⁰

Explanation:

Given that; Diameter is 8.40 cm,

Radius (R) = D/2 = 8.40/2 = 4.20 cm = 0.042 m

Number of turns (N) = 17

Current in the loop (I) = 3.20 A

Magnetic field (B) = 0.610 T

Let the angle between the loop's area vector A and the magnetic field B be

Now. the area of the loop is;

A = πR²

A = 3.14 ( 0.042 )²

A =  0.005539 m²

Torque on the loop (t) = NIABsinФ

t = 17 × 3.20 ×0.005539 × 0.610 × sinФ

t = 0.1838sinФ N.m

for the torque to be maximum, sin should be maximum

i.e (sinФ)maximum = 1

therefore the Maximum torque is

Tmax = 0.1838 × 1 = 0.1838  N.m

Given the torque is 71.0% of its maximum value

t = 0.71 × tmax

t = 0.71 × 0.1838

t = 0.1305

Now

0.1305 N.m =  0.1838 sinФ N.m

sinФ = 0.1305 / 0.1838

sinФ = 0.71001

Ф = sin⁻¹ 0.71001

Ф  = 45.24⁰ ≈ 45⁰

Answer:

The period of motion is 0.5 second.

Explanation:

Given;

extension of the spring, x = 3.8 cm = 0.038 m

mass of the object, m = 13 g = 0.013 kg

Determine the force constant of the spring, k;

F = kx

k = F / x

k = mg / x

k = (0.013 x 9.8) / 0.038

k = 3.353 N/m

When the object is replaced with a block of mass 20 g, the period of motion is calculated as;

[tex]T = 2\pi\sqrt{\frac{m}{k} } \\\\T = 2\pi\sqrt{\frac{0.02}{3.353} } \\\\T = 0.5 \ second[/tex]

Therefore, the period of motion is 0.5 second.

Answer:

The amplitude of the resultant wave is 12.93 cm.

Explanation:

The amplitude of resultant of two waves, y₁ and y₂, is given as;

Y = y₁ + y₂

Let y₁ = A sin(kx - ωt)

Since the wave is out phase by φ, y₂ is given as;

y₂ = A sin(kx - ωt + φ)

Y = y₁ + y₂ = 2A Cos (φ / 2)sin(kx - ωt + φ/2 )

Given;

phase difference, φ = 45°

Amplitude, A = 7.00 cm

Y = 2(7) Cos (45 /2) sin(kx - ωt + 22.5° )

Y = 12.93 cm

Therefore, the amplitude of the resultant wave is 12.93 cm.

Answer:

The energy of one of its photons is 1.391 x 10⁻¹⁸ J

Explanation:

Given;

wavelength of the UVC light, λ = 142.9 nm = 142.9 x 10⁻⁹ m

The energy of one photon of the UVC light is given by;

E = hf

where;

h is Planck's constant = 6.626 x 10⁻³⁴ J/s

f is frequency of the light

f = c / λ

where;

c is speed of light = 3 x 10⁸ m/s

λ  is wavelength

substitute in the value of f into the main equation;

E = hf

[tex]E = \frac{hc}{\lambda} \\\\E = \frac{6.626*10^{-34} *3*10^{8}}{142.9*10^{-9}} \\\\E = 1.391*10^{-18} \ J[/tex]

Therefore, the energy of one of its photons is 1.391 x 10⁻¹⁸ J

Answer:

An aircraft, flying in the vicinity of 18,000 ft altitude from west to east over the US at 12 Z today, will __LOSE___ altitude if the altimeter is not corrected

Explanation:

According to Ohms Law :

V = I * R

(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms

Also,

[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]

(B)

[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]

Drift speed is missing. It is given as;

1.7 × 10^(-5) m/s

A) R = 0.0293 ohms

B) ρ = 1.589 × 10^(-8)

C) n = 8.8 × 10^(28) electrons

This is about finding, resistance and resistivity.

Length; L = 5.8 m

Diameter; d = 2mm = 0.002 m

Radius; r = d/2 = 0.001 m

Voltage; V = 22 mv = 0.022 V

Current; I = 750 mA = 0.75 A

Area; A = πr² = 0.001²π

Drift speed; v_d = 1.7 × 10^(-5) m/s

R = V/I

R = 0.022/0.75

R = 0.0293 ohms

ρ = RA/L

ρ = (0.0293 × 0.001²π)/5.8

ρ = 1.589 × 10^(-8)

J = n•e•v_d

Where;

J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²

e is charge on an electron = 1.6 × 10^(-19) C

v_d = 1.7 × 10^(-5) m/s

n is number of free electrons per unit volume

Thus;

238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))

238732.44 = (2.72 × 10^(-24))n

n = 238732.44/(2.72 × 10^(-24))

n = 8.8 × 10^(28)

Read more at; brainly.com/question/17005119

Answer:

Thomas is correct that the zero displacements

Lilian is right that the distance is greater than zero.

Explanation:

In this problem we have to be clear about the difference between displacement and distance.

The displacement is a vector, that is, it has a modulation and direction, in this case we can draw a vector for the outward trip and another vector for the return trip, both will have the same magnitude, but their directions are opposite, so the resulting vector is zero.

The distance is a scalar and its value coincides with the modulus of the distance vector, in our case the distance is d for the outward journey and d for the return journey, so the total distance is 2d, which is different from zero.

The two students have some reason, but neither complete,

The displacement is zero because it is a vector and

the distance is different from zero (2d) because it is a scalar

Thomas is correct that the zero displacements

Lilian is right that the distance is greater than zero.

Therefore I agree with both, because each one has a 50% of the reason

Answer:

[tex]\boxed{\sf 65.3 \ inches}[/tex]

Explanation:

1 foot = 12 inches

Sammy is 5 feet tall.

5 feet = ? inches

Multiply the feet value by 12 to find in inches.

5 × 12

= 60

Add 5.3 inches to 60 inches.

60 + 5.3

= 65.3

Answer:

Acceleration of the body is:

[tex]a=0.27\,\,m/s^2[/tex]

Explanation:

Use Newton's second Law to solve for the acceleration:

[tex]F=m\,\,a\\a=\frac{F}{m} \\a=\frac{4\,N}{15\,\,kg} \\a=0.27\,\,m/s^2[/tex]

Answer:

1) designed to measure the difference in speed of light in different directions , 1887

Explanation:

1) This experiment was designed to measure the difference in speed of light in different directions and therefore find the speed of the ether.

2) was made in 1887

3) At that time it was assumed that it was the medium in which light traveled and it is everywhere

4) the speed of the wave depends on the characteristics of the medium where it travels,

for the one in a string depends on the tension and density

for an electromagnetic wave of the permittivity and permeability of the vacuum

5) In this type of interferometer the beam is divided into two rays

6) In his interrupter, he had to accurately measure the displacement of the fringes in a telescope, for which he had to minimize vibrations, he had problems in the movement of one of the arms, changes in temperature

7) In Michelsom's second experiment, the apparatus could measure 0.01 fringes by increasing the length of the arms by 11 m

8) The new interferometer floated on a bed of mercury

9) Couldn't measure any difference in speed of light in different directions

10) Physics was forced to eliminate the concept of ETHER

11) One of the principles of relativities that the speed of light is constant in all inertial efficiency systems

12) Michelson in 1907

13) It seems that Einstein did not know the results of this experiment

Answer:

The mass of the object is 3.08 kg.

Explanation:

The horizontal force is12.7 N and the coefficient of the kinetic fraction are 0.42. Now we have to compute the mass of the object. Thus, use the below formula to find the mass of the object.

Let the mass of the object = m.

The coefficient of kinetic friction, n = 0.42

Therefore,  

Force, F = n × mg

12.7 = 0.42 × 9.8 × m

m = 3.08 kg

The mass of the object is 3.08 kg.

Answer:

 f = - 20 cm

Explanation:

This exercise asks us for the focal length, which for a lens in air is

                  1 / f = (n₂-n₁) (1 / R₁ - 1 / R₂)

where n₂ is the refractive index of the material, n₁ is the refractive index of the medium surrounding the lens, R₁ and R₂ are the radii of the two surfaces.

In this exercise the medium that surrounds the lens is air n₁ = 1 and the lens material has an index of refraction n₂ = n = 1.50, let's substitute in the expression

                 - 1/40 = (n-1) (1 / R₁ -1 / R₂)

                (1 / R₁ - 1 / R₂) = - 1/40 (n-1)

let's calculate

               (1 / R₁ -1 / R₂) = - 1/40 (1.50 -1)

               (1 / R₁ -1 / R₂) = -1/20

 Now we change the construction material for one with refractive index

n = 2, keeping the radii,

              1 / f = (n-1) (1 / R₁-1 / R₂)

              1 / f = (n-1) (-1/20)

let's calculate

             1 / f = (2.00-1) (-1/20)

              1 / f = -1/20

              f = - 20 cm

Answer:

The rms current in the circuit is 3.513 A

Explanation:

Given;

angular frequency of the inductor, ω = 363 rad/s

maximum voltage of the inductive AC, V₀ = 169 V

Inductance of the inductor, L = 0.0937 H

Inductive reactance is given by;

[tex]X_L = 2\pi f L= \omega L[/tex]

[tex]X_L = 363 *0.0937\\\\X_L = 34.0131 \ ohms[/tex]

The rms voltage is given by;

[tex]V_{rms} = \frac{V_o}{\sqrt{2} } \\\\V_{rms} =\frac{169}{\sqrt{2} } \\\\V_{rms} = 119.5 \ V[/tex]

The rms current in the circuit is given by;

[tex]I_{rms} = \frac{V_{rms}}{X_L} \\\\I_{rms} = \frac{119.5}{34.0131} \\\\I_{rms} = 3.513 \ A[/tex]

Therefore, the rms current in the circuit is 3.513 A

Answer:

The magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.

Explanation:

The initial centripetal acceleration, a of the race-car around the circular track of radius , R with a linear speed v is a = v²/R.

When the linear speed of the race-car increases to v' = 4v, the centripetal acceleration a' becomes a' = v'²/R = (4v)²/R = 16v²/R.

So the centripetal acceleration, a' = 16v²/R.

To know how much the magnitude of the car's centripetal acceleration changes, we take the ratio a'/a = 16v²/R ÷ v²/R = 16

a'/a = 16

a' = 16a.

So the magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.

Answer:

constructive interferencia  0, 1 , 2 m

destructive inteferencia   1/4, 3/4. 5/4, 7/4 m

Explanation:

This exercise is equivalent to the double slit experiment, the two sources are in phase and separated by a distance, therefore the waves observed in the line between them have an optical path difference and a phase difference, given by the expression

            Δr / λ = Φ / 2π

            Δr = Φ/2π   λ

let's apply this expression to our case

λ = 1 m

            Δr = Φ 1 / 2π

We have constructive interference for angle of  Φ = 0, 2π, ...

let's find the values ​​where they occur

  Φ         Δr

   0          0

  2π         1

  4π        2

Destructive interference occurs by    Φ = π /2, 3π / 2, ...

 Φ          Δr

 π/2       ¼ m

 3π /2    ¾ m

5π /2     5/4 m

7π /2      7/4 m

Answer:

A The father should sit closer to the pivot.

C The longer wrench makes the job easier because less force is needed when there is more distance from the pivot.

A As far from the head of the hammer as possible because this will maximize torque.

D at the opposite side of the seesaw towards the middle

:) gl

Explanation:

If a father and his son want to play on a seesaw then to balance the torque of the seesaw the father should sit near the pivot as he had more weight as compared to his son, while the son should sit a little farther from the pivot point as compared to his father.

Mechanical advantage is defined as a measure of the ratio of output force to input force in a system, It is used to analyze the forces in simple machines like levers and pulleys.

Mechanical advantage = output force(load) /input force (effort)

As given in the problem statement If a father and his son wish to play on a seesaw,

The father should sit close to the pivot because he weighs more than his son, and the son should sit a little farther away from the pivot point than his father. This will help balance the torque of the seesaw.

Thus, the father should sit near the pivot on the one side and the son should sit a little farther from the pivot of a seesaw on the other side.

Learn more about Mechanical advantages, here

brainly.com/question/16617083

#SPJ2

Answer:

The answer is "45.79 m/s"

Explanation:

Given values:

diameter= 25 cm

w= 3500 rpm

Formula:

[tex]\boxed{v=w \times r} \ \ \ \ \ \ _{where} \ \ \ w = \frac{rad}{s} \ \ \ and \ \ \ r = meters[/tex]

Calculating r:

[tex]r= \frac{diameter}{2}[/tex]

  [tex]=\frac{25}{2}\\\\=12.5 \ cm[/tex]

converting value into meters: [tex]12.5 \times 10^{-2} \ \ meter[/tex]

calculating w:

[tex]w= diameter \times \frac{2\pi}{60}\\[/tex]

   [tex]= 3500 \times \frac{2\times 3.14}{60}\\\\= 3500 \times \frac{2\times 314}{6000}\\\\= 35 \times \frac{314}{30}\\\\= 35 \times \frac{314}{30}\\\\=\frac{10990}{30}\\\\=\frac{1099}{3}\\\\=366.33[/tex]

w= 366.33 [tex]\ \ \frac{rad}{s}[/tex]

Calculating v:

[tex]v= w\times r\\[/tex]

  [tex]= 366.33 \times 12.5 \times 10^{-2}\\\\= 366.33 \times 12.5 \times 10^{-2}\\\\= 4579.125 \times 10^{-2}\\\\\boxed{=45.79 \ \ \frac{m}{s}}[/tex]

Answer:

A. We have that radius r = 4.00m intensity I = 8.00 W/m^

total power = power/ Area ( 4πr2)= 8.00 w/m^2( 4π ( 4.00 m)2=1607.68 W

b) I = total power/ 4πr2= 8.00 W/m2 ( 4.00 m/ 9.5 m)2= 1.418 W/m2

c) E = total power x time= 1607 . 68 W x 1s= 1607.68 J

Answer:

W = 122.3 J

Explanation:

First, we need to find out the force applied to the smaller piston. We know that the pressure applied to smaller piston must be equally transmitted to the larger piston. Therefore,

P₁ = P₂

F₁/A₁ = F₂/A₂

F₂ = F₁(A₂/A₁)

where,

F₁ = Force of Larger Piston = Weight of car = mg = (1500 kg)(9.8 m/s²)

F₁ = 14700 N

F₂ = Force applied to smaller piston = ?

A₁ = Area of larger piston = πd₁²/4

A₂ = Area of smaller piston = πd₂²/4

Therefore,

F₂ = (14700 N)[(πd₂²/4)/(πd₁²/4)]

F₂ = (14700 N)(d₂²/d₁²)

where,

d₁ = diameter of large piston = 50 cm

d₂ = diameter of small piston = 4 cm

Therefore,

F₂ = (14700 N)[(4 cm)²/(50 cm)²]

F₂ = 94.08 N

Now, for the work done on the car:

Work Done = W = F₂ d

where,

d = displacement of car = 1.3 m

Therefore,

W = (94.08 N)(1.3 m)

W = 122.3 J

Answer:

Explanation:

Using the lens formula

1//f = 1/u+1/v

f is the focal length of the lens

u is the object distance

v is the image distance

For convex lens

The focal length of a convex lens is positive and the image distance can either be negative or positive.

Given f = 20cm and u = 10cm

1/v = 1/f - 1/u

1/v = 1/20-1/10

1/v = (1-2)/20

1/V = -1/20

v = -20/1

v = -20 cm

Since the image distance is negative, this shows that the nature of the image formed by the convex lens is a virtual image

For concave lens

The focal length of a concave lens is negative and the image distance is negative.

Given f = -20cm and u = 10cm

1/v = 1/f - 1/u

1/v = -1/20-1/10

1/v = (-1-2)/20

1/V = -3/20

v = -20/3

v = -6.67 cm

Since the image distance is negative, this shows that the nature of the image formed by the concave lens is a virtual image