Answer:
a. Speed = 1.6 m/s
b. Amplitude = 0.3 m
c. Speed = 1.6 m/s
Amplitude = 0.15 m
Explanation:
a.
The frequency of the wave must be equal to the reciprocal of the time taken by the boat to move from the highest point to the highest point again. This time will be twice the value of the time taken to travel from the highest point to the lowest point:
frequency = [tex]\frac{1}{2(2\ s)}[/tex] = 0.25 Hz
The wavelength of the wave is the distance between consecutive crests of wave. Therefore,
Wavelength = 6.4 m
Now, the speed of the wave is given as:
Speed = (Frequency)(Wavelength)
Speed = (0.25 Hz)(6.4 m)
Speed = 1.6 m/s
b.
Amplitude is the distance between the mean position of the wave and the extreme position. Hence, it will be half the distance between the highest and lowest point:
Amplitude = (0.5)(0.6 m)
Amplitude = 0.3 m
c.
frequency = [tex]\frac{1}{2(2\ s)}[/tex] = 0.25 Hz
Speed = (Frequency)(Wavelength)
Speed = (0.25 Hz)(6.4 m)
Speed = 1.6 m/s
Amplitude = (0.5)(0.3 m)
Amplitude = 0.15 m
what term is used to describe the block of organs (heart, lungs, liver, kidneys and spleen) that are removed during the autopsy?
The term used to describe the block of organs that are removed during the autopsy is Thoracic organs.
The organs that are removed during autopsy include:
Thoracic organs;Cervical organs, and Abdominal organsThe thoracic cavity contains organs and tissues that function in the respirator, cardiovascular, nervous and digestive system.
These thoracic organs include the following;
heart, lungs, liver, kidneys and spleen.Thus, we can conclude that the term used to describe the block of organs that are removed during the autopsy is Thoracic organs.
Learn more here:https://brainly.com/question/25087653
Which statement best explains why objects are pulled toward Earth’s center?
Answer:
Earth has a much greater mass than objects on its surface
Question 2 of 20 :
Select the best answer for the question.
2. Which of the following is considered to be a vector?
A. Velocity
B. Time
C. Temperature
D. Mass
Mark for review (Will be highlighted on the review page)
The answer is A. velocity .
Velocity is a vector quantity because it need magnitude as well as direction to be defined.
red light from a He-Ne laser is at 590.5 nm in the air. it is fired at an angle of 31.0 to horizontal at a flat transparent crystal of calcite (n= 1.34 ar this frequency) .find the wavelength and frequency of the light inside the crystal and the angle from horizontal that it travels inside the calcite crystal.
Answer:
7374.4
Explanation:
I took the test
(filler so I can post)
The universe cooled after the Big Bang.At some point hydrogen atoms combined to form helium.What is this process called?
Answer:
Nuclear fusion
Explanation:
The nucleus of a certain type of uranium atom contains
92 protons and 143 neutrons. What is the total charge of
the nucleus?
Answer:
charge = electrons + protons
=92+92
=184
How much work will a 500 watt motor do in 10 seconds?
Answer:
50j
Explanation:
Watts are units used to measure power. power can be defined as rate of energy transfer
500 watts means - 500 J of energy per second
in 1 second - 500 J of work is done
therefore within 10 seconds - 500 J/s x 10 s = 5000 J
work of 5000 J is carried out in 10 seconds
Answer:
Watts are units used to measure power. power can be defined as rate of energy transfer
500 watts means - 500 J of energy per second
in 1 second - 500 J of work is done
therefore within 10 seconds - 500 J/s x 10 s = 5000 J
work of 5000 J is carried out in 10 seconds
Explanation:
Classify each change (which can be manipulated within the green box) according to its effect on the wavelength.
a. Decrease frequency
b. Decrease damping
c. Decrease amplitude
d. Increase frequency
e. Increase amplitude
f. Increase damping
g. Shortens wavelength
Answer:
Explanation:
The classification will be made into 3 categories, which are
Ones that shortens wavelengths
Ones that lengthens wavelengths
Ones that has no effect on wavelengths
Shortens wavelengths -> Increase frequency
Lengthens wavelengths -> Decrease frequency
No effect -> Increase amplitude, decrease amplitude, increase damping, decrease damping.
What is the magnitude of the gravitational force acting on a
1.0 kg object which is 1.0 m from another 1.0 kg object?
Ans[tex]^{}[/tex]wer and expl[tex]^{}[/tex]anation is in a fi[tex]^{}[/tex]le. Li[tex]^{}[/tex]nk below! Go[tex]^{}[/tex]od luck!
bit.[tex]^{}[/tex]ly/3a8Nt8n
A vertical spring with a spring constant of 420 N/m is mounted on the floor. From directly above the spring, which is unstrained, a 0.15-kg block is dropped from rest. It collides with and sticks to the spring, which is compressed by 3.7 cm in bringing the block to a momentary halt. Assuming air resistance is negligible, from what height above the compressed spring was the block dropped
Answer:
19.53 cm
Explanation:
The computation of the height is as follows:
Here we applied the conservation of the energy formula
As we know that
P.E of the block = P.E of the spring
m g h = ( 1 ÷ 2) k x^2
where
m = 0.15
g = 9.81
k = 420
x = 0.037
So now put the values to the above formula
(0.15) (9.81) (h) = 1 ÷2 × 420 × (0.037)^2
1.4715 (h) = 0.28749
h = 0.19537 m
= 19.53 cm
Consider a wheel (solid disk) of radius 1.12 m, mass 10 kg and moment of inertia 1 2 M R2 . The wheel rolls without slipping in a straight line in an uphill direction 37◦ above the horizontal. The wheel starts at angular speed 12.0536 rad/s but the rotation slows down as the wheel rolls uphill, and eventually the wheel comes to a stop and rolls back downhill. How far does the wheel roll in the uphill direction before it stops?
Answer:
d= 23.25 m
Explanation:
Assuming no other external forces acting on the disk, total mechanical energy must be conserved.Taking the initial height of the disk as the zero reference for the gravitational potential energy, initially. all the energy is kinetic.This kinetic energy is part translational kinetic energy, and part rotational kinetic energy, as follows:[tex]E_{o} = K_{transo} + K_{roto} (1)[/tex]
When the disk rolling uphill finally comes to an stop, its energy is completely gravitational potential energy, as follows:[tex]E_{f} = m*g*h (2)[/tex]
Since the angle with the horizontal of the track on which the disk is rolling, is 37º, we can express the height h in terms of the distance traveled d and the angle of 37º, as follows:[tex]h = d* sin 37 (3)[/tex]
Replacing (3) in (2):[tex]E_{f} = m*g* d * sin 37 (4)[/tex]
Since the wheel rolls without sleeping, this means that at any time there is a fixed relationship in the translational speed and the angular speed, as follows:[tex]v = \omega * R (5)[/tex]
For a solid disk, as mentioned in the question, the moment of inertia is just 1/2*M*R².The rotational kinetic energy of a rotating rigid body can be written as follows:[tex]K_{rot} = \frac{1}{2}* I * \omega^{2} (6)[/tex]
Replacing I from (6) and ω from (5), and remembering the definition of the translational kinetic energy, we can solve (1) in terms of v, m and r as follows:[tex]E_{o} = K_{transo} + K_{roto} = \frac{1}{2}* m* v^{2} +(\frac{1}{2}* \frac{1}{2}) *m*r^{2}*(\frac{v}{r}) ^{2} = \\ \frac{3}{4} * m * v^{2} (7)[/tex]
Since (4) and (7) must be equal each other, we can solve for d as follows:[tex]d =\frac{3}{4} * \frac{v^{2}}{g*sin37} = \frac{3}{4}*\frac{(\omega*r)^{2}}{g*sin 37} (8)[/tex]
Replacing by the values, we finally get:[tex]d =\frac{3}{4}*\frac{(\omega*r)^{2}}{g*sin 37} = \frac{3}{4} *\frac{(12.0536rad/sec*1.12m)^{2}}{9.8 m/s2*0.601} = 23. 25 m.[/tex]
Scientists are constantly exploring the universe, looking for new planets that support life similar to the life on
Earth. A new planet that supports life would have all of the following characteristics except -
A. a gaseous atmosphere.
B. an orbiting moon.
C. liquid water.
D. protection from radiation.
A new planet that supports life would have all the following characteristics except an orbiting moon. Hence, option B is correct.
What is a Planet?An enormous, spherical celestial object known as a planet is neither a star nor its remains. The nebular hypothesis, which states how an interstellar cloud falls out of a nebula to produce a young protostar encircled by a protoplanetary disk, is now the best explanation for planet formation.
By gradually accumulating material under the influence of gravity, or accretion, planets develop in this disk.
The rocky planets Mercury, Venus, Earth, and Mars, as well as the giant planets Jupiter, Saturn, Uranus, and Neptune, make up the Solar System's minimum number of eight planets. These planets all revolve around axes that are inclined relative to their respective polar axes.
To know more about Planet:
https://brainly.com/question/14581221
#SPJ2
What happens when Earth rotates on its axis and how long does it take
Answer:
You get Day and Night
It takes 24 hour
Answer:
Explanation:
The Earth's orbit makes a circle around the sun. At the same time the Earth orbits around the sun, it also spins.Since the Earth orbits the sun and rotates on its axis at the same time we experience seasons, day and night, and changing shadows throughout the day.It only takes 23 hours, 56 minutes and 4.0916 seconds for the Earth to turn once on its axis.
A radioactive material produces 1160 decays per minute at one time, and 4.0 h later produces 170 decays per minute. whats the half life
Answer:
Half life is 3.23 hours
Explanation:
Given
Decay rate at starting = 1160 decays per minute
Decay rate after 4 hours = 170 decays per minute
As we know know
[tex]N = N_0 *e ^{\Lambda *T}[/tex]
Substituting the given values, we get -
[tex]170 = 1160 *e ^{-4*\Lambda}\\0.1465 = e ^{-4*\Lambda}\\-0.834 = -4 * \Lambda\\\Lambda = 0.834/4\\\Lambda = 0.2085[/tex]
Also
[tex]t_{1/2} = \frac{ln2}{\Lambda}[/tex]
Substituting the given values we get -
[tex]t_{1/2} = =0.693/0.2085\\= 3.23[/tex]hours
If the acceleration of the body is towards the center, what is the direction of the unbalanced force ? Using a complete sentence , describe the direction of the net force that causes the body to travel in a circle at a constant speed.
Accelerating objects are changing their velocity. Velocity is often thought of as an object's speed with a direction. Thus, objects which are accelerating are either changing their speed or changing their direction. They are either speeding up, slowing down or changing directions. Changing the velocity in any one of these three ways would be an example of an accelerated motion.
A doorknob is a type of wheel and axle. In a doorknob, the door handle acts as the wheel. The handle is connected to a cylinder, called a spindle, which acts as the axle. When the handle turns, the spindle turns in the same direction. The spindle is located inside the handle and pulls the latch back and forth, allowing the door to open.
In the doorknob shown above, when the handle is rotated a distance of 84 millimeters, the spindle is rotated a distance of 14 millimeters. What is the mechanical advantage of this doorknob?
A. 504
B. 6
C. 84
D. 14
can someone please take there time and answer this for me :)
Answer:
number 1
Explanation:
they have common ancestors
Swordfish are capable of stunning output power for short bursts. A 650 kg swordfish has a cross-sectional area of 0.92 m2 and a drag coefficient of 0.0091- very low due to some evolutionary adaptations. Such a fish can sustain a speed of 30 m/s for a few seconds. Assume seawater has a density of 1026 kg/m3. a) How much power does the fish need to put out for motion at this high speed
Answer:
the required or need power is 115960.57 Watts
Explanation:
First of all, we take down the data we can find from the question, to make it easier when substituting values into formulas.
mass of swordfish m = 650 kg
Cross - sectional Area A = 0.92 m²
drag coefficient C[tex]_D[/tex] = 0.0091
speed v = 30 m/s
density p = 1026 kg/m³
Now, we determine our Drag force F[tex]_D[/tex]
Drag force F[tex]_D[/tex] = [tex]\frac{1}{2}[/tex] × C[tex]_D[/tex] × A × p × v²
Next, we substitute the values we have taken down, into the formula.
Drag force F[tex]_D[/tex] = [tex]\frac{1}{2}[/tex] × 0.0091 × 0.92 × 1026 × (30)²
Drag force F[tex]_D[/tex] = 4.294836 × 900
Drag force F[tex]_D[/tex] = 3865.3524
Now, we determine the power needed P[tex]_w[/tex]
P[tex]_w[/tex] = F[tex]_D[/tex] × v
we substitute
P[tex]_w[/tex] = 3865.3524 × 30
P[tex]_w[/tex] = 115960.57 Watts
Therefore, the required or need power is 115960.57 Watts
When two substances that cannot dissolve each other are mixed, a ________ mixture is formed
Answer: hetero i think i dont know
Explanation:
Answer:
When two substances that cannot dissolve each other are mixed, a mixture is formed.
i hope this helps a little bit.
Which is the best analogy of a wave?
A wave is like building a ramp.
A wave is like shaking a hand.
A wave is like water rippling in a pond.
A wave is like knocking down a building.
Answer:
c i think
Explanation:
Answer:
answer is C
Explanation:
An ideal horizontal spring-mass system has a mass of 1.0 kg and a spring with constant 78 N/m. It oscillates with a period of 0.71 seconds. When this same spring-mass system oscillates vertically instead, the period is _______ seconds. Enter 2 significant figures (a total of three digits) and use g = 10.0 m/s2 if necessary.
Answer:
T = 0.71 seconds
Explanation:
Given data:
mass m = 1Kg, spring constant K = 78 N/m, time period of oscillation T = 0.71 seconds.
We have to calculate time period when this same spring-mass system oscillates vertically.
As we know
[tex]T = 2\pi \sqrt{\frac{m}{K} }[/tex]
This relation of time period is true under every orientation of the spring-mass system, whether horizontal, vertical, angled or inclined. Therefore, time period of the same spring-mass system oscillating vertically too remains the same.
Therefore, T = 0.71 seconds
A ball is attached to one end of a wire, the other end being fastened to the ceiling. The wire is held horizontal, and the ball is released from rest. It swings downward and strikes a block initially at rest on a horizontal frictionless surface. Air resistance is negligible, and the collision is elastic. The masses of the ball and block are, respectively, 1.48 kg and 2.77 kg, and the length of the wire is 1.11 m. Find the velocity of the ball just after the collision.
Answer: Velocity of the ball just after the collision is -1.414 m/s.
Explanation:
As energy is conserved in a reaction so here, energy before collision will be equal to the energy after collision.
[tex]E_{before} = mgh = E_{after} = \frac{1}{2}mv_{o}^{2}[/tex]
where,
m = mass
g = gravitational energy = [tex]9.8 m/s^{2}[/tex]
h = height or length
[tex]v_{o}[/tex] = initial velocity
Also here, height is the length of wire. Let the height be denoted by 'L'. Therefore,
[tex]\frac{1}{2}mv_{o}^{2} = mgL\\v_{o}^{2} = 2gL\\v_{o} = \sqrt{2gL}\\= \sqrt{2 \times 9.8 m/s^{2} \times 1.11 m}\\= 4.66 m/s[/tex]
Formula used to calculate velocity after the collision is as follows.
[tex]v_{f ball} = v_{o} [\frac{m_{ball} - m_{block}}{m_{ball} + m_{block}}][/tex]
where,
[tex]v_{f ball}[/tex] = final velocity of ball after collision
[tex]m_{ball}[/tex] = masses of ball
[tex]m_{block}[/tex] = masses of block
Substitute the values into above formula as follows.
[tex]v_{f ball} = v_{o} [\frac{m_{ball} - m_{block}}{m_{ball} + m_{block}}]\\= 4.66 m/s [\frac{1.48 kg - 2.77 kg}{1.48 kg + 2.77 kg}]\\= 4.66 m/s \times (-0.303)\\= -1.414 m/s[/tex]
Thus, we can conclude that velocity of the ball just after the collision is -1.414 m/s.
whem completing an emergency Roaside stop,it is necessary to put on your parking brake
A. True
B. False
Answer:
trueeeeeeee..........mmmm...........
A circuit is built based on this circuit diagram.
What is the equivalent resistance of the circuit?
0.61 Ω
Ο 1.6 Ω
7.5Ω
Ο 18 Ω
12V
3.0 Ω.
6.0 Ω
9.Ο Ω.
Will mark brainlyest. No “links” I don’t want them
[tex]\mathfrak{\huge{\orange{\underline{\underline{AnSwEr:-}}}}}[/tex]
Actually Welcome to the concept of resistors,
The equivalent circuit is given as,
1/Rp = 1/3 + 1/6 + 1/9
1/Rp = 6+3+2/18
1/Rp = 11/18
Rp = 18/11 ==> 1.63 ==> 1.6 ohms
hence the equivalent resistance of the circuit is 1.6 ohms
The equivalent resistance of the circuit is 1.6Ω. The correct option is B.
What is Ohm’s law?Ohm’s law state that ” At constant temperature, the current (I) flowing through a conductor is directly proportional to the potential difference(V) across the two endpoints of the given conductor.”
I.e V ∝ I
V=IR
Where V= potential difference across the conductor.
I = current flowing through the conductor.
R= constant pf proportionality i.e resistance which unit is ohm(Ω).
There are two ways we can connect the resistors.
(i) series connection
If a number of resistors are said to be connected in series When the same current (I) flows through them.
Let R1, R2, and R3 be the resistors connected in series.
Then the R equivalent is
Req=R1+R2+R3
(ii) parallel connection
A number of resistors are said to be connected in parallel when the same potential difference(V) exists across each of them.
Let R1, R2, and R3 be the resistors connected in parallel.
Then the R equivalent is
1/Req=1/R1+1/R2+1/R3
In this question,
The three resistance connected in parallel by applying the above formula we get,
1/Req=1/R1+1/R2+1/R3
1/Req = 1/3 + 1/6 + 1/9 ................. (∵R1=3Ω,R2=6Ω AND R3=9Ω)
1/Req =11/18
Req=18/11
Req=1.6363Ω
Req≈1.6Ω
Therefore, The equivalent resistance of the circuit is 1.6Ω.
To learn more about resistance click:
https://brainly.com/question/29427458
#SPJ7
What organ in the digestive system ABSORBS NUTRIENTS from broken down food?
Answer:
The small intestine absorbs most of the nutrients in your food, and your circulatory system passes them on to other parts of your body to store or use. Special cells help absorbed nutrients cross the intestinal lining into your bloodstream.
Explanation:
mdjxjxjcjfkfjjdksklqlakzjxjxkkskakMmznxkxkdkd?
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
I hope this helped!+*
03: A mass with a 60 g vibrate at the end of a spring. The amplitude of the motion is 0.394 ft
and a frequency is 0.59 HZ. Find the perind and spring constant, the maximum speed and
acceleration of the mass, the speed and acceleration when the displacement is 6 cm, compute the
kinetic and the potential energy when the position is 6 cm
Answer:
a) T = 1.69 s, b) k = 0.825 N / m, c) v = 1.46 feet/s, d) a = 5.41 ft / s²,
e) v = - 1,319 ft / s, a = - 2.70 ft / s², f) K = 4.8 10⁻³ J, U = 1.49 10⁻³ J
Explanation:
In a mass-spring system with simple harmonic motion, the angular velocity is
w = [tex]\sqrt{\frac{k}{m} }[/tex]
a) find the period
angular velocity, frequency, and period are related
w = 2π f = 2π / T
f = 1 / T
T = 1 / f
T = 1 / 0.59
T = 1.69 s
b) the spring constant
w = 2π f
w = 2π 0.59
w = 3.70 rad / s
w² = k / m
k = w² m
k = 3.70² 0.060
k = 0.825 N / m
c) the maximum speed
simple harmonic movement is described by the expression
x = A cos (wt + Ф)
speed is defined by
v =[tex]\frac{dx}{dt}[/tex]
v = -A w sin (wt + fi)
the speed is maximum when the cosine is ± 1
v = A w
v = 0.394 3.70
v = 1.46 feet/s
d) maximum acceleration
a = [tex]\frac{dv}{dt}[/tex]
a = - A w² cos wt + fi
the acceleration is maximum when the cosine is ±1
a = A w²
a = 0.394 3.70²
a = 5.41 ft / s²
e) velocity and acceleration for x = 6 cm
let's reduce the cm to feet
x = 6 cm (1 foot / 30.48 cm) = 0.1969 foot
Before doing this part we must find the phase angle (Ф), the most common way to start the movement is to move the spring a small distance and release it, so its initial speed is zero for t = 0 s
let's use the expression for the velocity
v = -A w sin (0 + Фi)
0 = - A w sin Ф
so sin Ф = 0 which implies that Фi = 0
the equation of motion is
x = A cos wt
x = 0.394 cos 3.70t
we substitute
0.1969 = 0.394 cos 370t
3.70 t = cos⁻¹ (0.1969 / 0.394)
let's not forget that the angle is in radians
3.70, t = 1.047
t = 1.047 / 3.70
t = 0.2826 s
we substitute this time in the equation for velocity and acceleration
v = - Aw sin wt
v = - 0.394 3.70 sin 3.70 0.2826
v = - 1,319 ft / s
a = - A w² cos wt
a = - 0.394 3.70² cos 3.70 0.2826
a = - 2.70 ft / s²
f) the kinetic and potential energy at this point
K = ½ m v²
let's slow down to the SI system
v = 1.319 ft / s (1 m / 3.28 ft) = 0.402 m / s
K = ½ 0.060 0.402²
K = 4.8 10⁻³ J
U = ½ k x²
U = ½ 0.825 0.06²
U = 1.49 10⁻³ J
an object is moving at 60m/s and has a mass of 5 kg what is its momentum
Answer:
300
Explanation:
the momentum is 300
p=mv
p=5×60
5×60 =300
15 points!
a. Calculate the electric potential energy stored in a 1.4 x 10-7 F capacitor
that stores 3.40 x 10-6 C of charge at 24.0 V.
Answer:
[tex]4.12\times 10^{-5}\ J[/tex].
Explanation:
Given that,
Capacitance, [tex]C=1.4\times 10^{-7}\ F[/tex]
Charge stored in the capacitor, [tex]Q=3.4\times 10^{-6}\ C[/tex]
We need to find the electric potential energy stored in the capacitor. The formula for the electric potential energy stored in the capacitor is given by :
[tex]E=\dfrac{Q^2}{2C}[/tex]
Put all the values,
[tex]E=\dfrac{(3.4\times 10^{-6})^2}{2\times 1.4\times 10^{-7}}\\\\=4.12\times 10^{-5}\ J[/tex]
So, the required electric potential eenergy is equal to [tex]4.12\times 10^{-5}\ J[/tex].
During transpiration, water goes from a _____ to a _____.
Answer:
WATER TO A VAPOR
Explanation:
Explanation:
During transpiration, water goes from a root to a stomata.